Life Fitness SM83 Instrukcja Użytkownika

M051-K50-B105 18 STACK MULTI-JUNGLE (SM83)WITH 3 ADJUSTABLE PULLEYSUNPACKING AND ASSEMBLY INSTRUCTIONS

SM83 Unpacking & Assembly Instructions10C. Prepare the weight stack. Slide the guide rods (2) through the weight stacks (1)as shown below. Place

SM83 Unpacking & Assembly Instructions116. Using a 7/8” combination wrench, bolt the floating pulleys into the 190 lb weightstacks (except for th

SM83 Unpacking & Assembly Instructions128. Mount the seated row and lat benches to the frame. Using the bolts specified inFigure 14 and a 9/16” s

SM83 Unpacking & Assembly Instructions13INSTALLING THE CABLESThe SM83 uses eight cables. There are three different types of cable used on the SM83

SM83 Unpacking & Assembly Instructions14ADJUSTABLE CROSSOVER CABLE ROUTINGOnce you’ve removed the pulleys as described previously, route the three

SM83 Unpacking & Assembly Instructions15Figure 18. Adjustable crossover cable end detail.Using a 7/8” wrench, tighten the jam nut onto the adjusta

SM83 Unpacking & Assembly Instructions16Bolt the cable to the weight stacks as shown in Figure 20. Thread the 7/8” nut up on thecable bolt as show

SM83 Unpacking & Assembly Instructions17 TRICEP PUSHDOWN CABLE ROUTINGRoute the tricep pushdown cable as shown in Figure 22. Screw the cable into

SM83 Unpacking & Assembly Instructions18 HARDWARE0123456½½½½½½Hardware Figure 1. Assembly Parts.

SM83 Unpacking & Assembly Instructions19The parts shown in Hardware Figure 1 are used to assemble the SM83. They are:A. 7/16” x 6” hex head bolt

SM83 Unpacking & Assembly Instructions2The SM83 comes partially assembled. Follow the steps below to complete the assembly.WARNING: COMPONENTS OF

SM83 Unpacking & Assembly Instructions20The part shown in Hardware Figure 3 is the 9/16” cable jam nut that’s used to secure thecables to the weig

SM83 Unpacking & Assembly Instructions21Hardware Figure 5. Top assemblies.S. Teardrop pulleys (bolt on above lat and seated row benches)T. 56” Lat

SM83 Unpacking & Assembly Instructions22Hardware Figure 6. Weight stack rubber bumpers.W. Weight stack rubber bumpers (inserted under weight stack

SM83 Unpacking & Assembly Instructions23PARTS LISTPart # ID Description QuantityMain components123456789CubesLow row benchLat benchConnecting beam

SM83 Unpacking & Assembly Instructions240017-00101-14130017-00104-03680017-00103-0217Pulley hardware(installed)1-3/4” BoltCap washer3/8” Nyloc nut

SM83 Unpacking & Assembly Instructions3 UNPACKINGFollow the steps below when unpacking the components of the SM83.1. Cut off the shipping wrapper

SM83 Unpacking & Assembly Instructions4 ASSEMBLYFigure 2 shows an assembled SM83.Figure 2. SM83 main components (seats and cables removed for clar

SM83 Unpacking & Assembly Instructions5Figure 3. Set the weight stack cubes.2. Bolt on the teardrop pulley assemblies above the benches (see Figu

SM83 Unpacking & Assembly Instructions6Figure 4. Bolt on the teardrop pulleys.Figure 5. Configuration for 2-3/4” and 3” bolts.3. Using a 5/8” soc

SM83 Unpacking & Assembly Instructions77/16” x 6” (2)-mount on topsRemove pulleys from housings to give clearance to socket extensionFigure 6. Bol

SM83 Unpacking & Assembly Instructions84. Using a 5/8” socket and combination wrench, mount the 56” lat tops (part T fromHARDWARE section) to the

SM83 Unpacking & Assembly Instructions9Figure 9. Mount rubber bumpers and the weight stacks.5. Install the weight stacks. To do this:A. Using a