Life-fitness 8205 Instrukcja Użytkownika

1Part # 6790401 Revision: 7/13/988205 CABLE CROSS OVER ASSEMBLY INSTRUCTIONS

10 FIGURE 7 FIGURE 8• SECURELY assembly the CENTER PULLEYBRACKETS (3) to the WEIGHT STACK SHAFTS(16) using one 1/2 X 1-1/4 BOLT (35) as shown

11 FIGURE 10• Insert the two GUIDE RODS (10) into the base of theTOWER (1) as shown in FIGURE 10. Lubricate theGUIDE RODS with a slicon or tef

12 FIGURE 11STEP 11:• Carefully slide the HEAD PLATE ASSEMBLY (17) downover the GUIDE RODS (10) onto the weight stack asshown in FIGURE 11.• Ru

STEP 12 FIGURE 12• SECURELY assemble the TOWER BRACE (4) to the TOWER (1) using two 1/2 X 4” BOLTS (37), two 1/2” WASHERS (27), and two 1/2” LO

14 FIGURE 13• Loop the threaded end of the CABLE (18) around a 4-1/2” PULLEY (13) and SECURELY assemble the 4-1/2”PULLEY (13) to the UPPER PULLE

15 FIGURE 15STEP 14:• Route the threaded end of the CABLE (18) through theLOWER PULLEY HOUSING (6) as shown in FIGURE 14.• Slip one 4-1/2” PU

16STEP 16 FIGURE 16• Attach one 5/16” SNAP HOOK (24) and one STRAP (15) to the ballend of the CABLE (18). See FIGURE 16.18• Screw the threaded

FIGURE 1717• SECURELY assemble the SHROUD (11) to the TOWER (1) using four 3/8 X 1” BUTTON HEAD CAP SCREWS (31) as shown in FIGURE 17.STEP 17:0

FIGURE 1818• Make sure all connections are tight and secure.STEP 18:Thank you for purchasing the LifeFitness 8205CABLE CROSS OVER. If unsure of

IMPORTANT NOTESPlease note:Tools Required for Assembly* Thank you for purchasing the LIFE FITNESS 8205 CABLE CROSS OVER. Please read these instruction

3PARTS LISTPART #6788503674410267890026744803678910267894036789703678820367881036459401678560232024023116101311620167932016284501671460167901016020601

4STEP 1 FIGURE 1• LOOSELY assemble the two LOWER PULLEY HOUSINGS (6) to the two TOWERS (1) using four 1/2 X 4” BOLTS (37) and four 1/2” LOCK NUTS

501 2 3 4 5 61/2 1/2 1/2 1/2 1/2 1/2STEP 2 FIGURE 2• LOOSELY assemble the two UPPER PULLEY HOUSINGS (8) to the two TOWERS (1) using two 1/2 X 3-

6STEP 3 FIGURE 3• SECURELY assemble two 3-1/2” PULLEYS (14) to the two NOVATRAK SWIVELS (2) using two 3/8 X 2” BOLTS (33) and two 3/8” LOCK NUTS

01 2 3 4 5 61/2 1/2 1/2 1/2 1/2 1/27STEP 4 FIGURE 4• LOOSELY assemble the two SWIVEL UPRIGHTS (7)to the LOWER PULLEY HOUSING (6) using four 1/2X

8STEP 5 FIGURE 5 91/2 X 1-1/4” 35 830 LOW HT. 7• SECURELY assemble the CHIN-UP SUPPORT (9) tothe two UPPER PULLEY HOUSINGS (8) using six1/2 X 1

01 2 3 4 5 61/2 1/2 1/2 1/2 1/2 1/29 FIGURE 6• Loop the ball end of the CABLE (18) around one 4-1/2” PULLEY (13) and SECURELY assemble the 4-1/2