G7 CABLE MOTION™ GYM SYSTEMUSER GUIDEWARNING:Read and follow all directions for each step to insure proper assemblyof this product.CLASS HPART # 83521
10STEP 4: Remove the protective paper from the SIDE SHROUD (23) before installation. Install one SIDE SHROUD (23) to the RIGHT TOWER (11) using six
11STEP 5 NOTE: INSTALL FROM THE INSIDE OF THE UNIT. Position two WEIGHT STACK CUSHIONS (20) and GUIDE RODS (16) at the GUIDE ROD BRACKET (G) on theRI
12STEP 6: Uncoil cables to remove all twists. Remove the UPPER PULLEYS (H) on the RIGHT TOWER (11) and LEFT TOWER (1) by removing the M10 x 50mmSCR
13STEP 7: Insert the threaded end of the CABLE (21) where UPPER PULLEY (H) was located. Lower the CABLE (21) down the long vertical tube that is in
14STEP 8: Dissemble one QUICK CONNECT by removing the two M5 HEX SCREWS (T) from the QUICK CONNECT COU-PLER (U). Carefuly remove the QUICK CONNECT SP
15STEP 9: Make adjustments to the HEAD PLATE PULLEY (19) and the threaded cable end to adjust cable length and toensure the cable is taut. If the t
16STEP 10: Install the FOOT EXTENSIONS (22) to the BOTTOM BRACKET TUBES (4) using four M10 x 20mm SCREWS (26)and four M10 WASHERS (27) on each side.
17STEP 11: Attach the six KIOSK BRACKETS (24) to the RIGHT TOWER (11) and LEFT TOWER (1) using two M5 HEXSCREWS (28) and two M6 WASHERS (29) each. Ti
18STEP 12: Adjust the rollers if the ROLLER CARRIAGE (Q) rolls up and down the tube with difficulty, or if it seems to sloppy. Unscrew the cable end
19MAINTENANCEPlease note:* We recommend cleaning your product (pads and frame) on a regular basis, usingwarm soapy water. Touch-up paint can be purcha
2TABLE OF CONTENTSSafety Statement . . . . . . . . . . . . . . . .2 Assembly Instructions . . . . . . . . . . . . . .7Gym Dimensions. . . . . . . .
20LIMITED WARRANTYLife Fitness® G7 Cable Motion™ Gym SystemLife Fitness extends the following LIMITED WARRANTY to the original owner (proof of purchas
LIFE FITNESS5100 NORTH RIVER ROAD.SCHILLER PARK, IL 60176 U.S.A.Tel: 1.847.288.3300 Fax: 1.800.216.88931.800.351.3737 (Toll-free within the U.S. an
3GYM DIMENSIONS Weight: 720 lbsResistance Ratio: 1:2
ITEM NO. QTY. PART NO. DESCRIPTION1 1 8172901 LEFT TOWER2 1 8178003 TOP BRACKET TUBE3 1 8178002 MIDDLE BRACKET TUBE4 1 8178004 BOTTOM BRACKET TUBE5 1
5HARDWARE LISTED BELOWITEM NO. QTY. PART NO. DESCRIPTION26 32 3256201 M10 X20MM SCREW27 52 3264201 M10 WASHER28 20 3242201 M5 HEX SCREW29 20 3264101 M
6HARDWARE:
7NOTE: Two person assembly is recommended.STEP 1: Make sure the LEFT TOWER (1) and the RIGHT TOWER (11) are positioned correctly prior to assembly. T
8STEP 2: Attach the CHIN UP BAR (12) between the LEFT TOWER (1) and RIGHT TOWER (11) using four M10 x 70mmSCREWS (33), eight M10 WASHERS (27), and fo
9STEP 3: Slide the top of the LEFT SLIDE TUBE ASSEMBLY (5) over the UPPER BRACKET (C) on the LEFT TOWER (1). NOTE: MAKE SURE THE ENGRAVED NUMBERS ON
Komentarze do niniejszej Instrukcji